Pozdrav.Imam instaliran Debian 4.0 i imam problema sa Broadcom NetLink BCM5906M mreznom.Da li neko zna kako mogu instalirati driver za ovu karticu.Hvala.
ako ne uspijes sa bcm driverima onda mozes sa ndiswraperom, kod mene bcm nije radio… ne znam zasto …
Nije rijec o Wireless kartici nego o klasicnoj ethernet kartici
sta je u stvari problem??
ne radi nikako ili?
de nam output od “dmesg | grep eth”
Pa ne radi , nije je poznao.Pokusao sam na internetu da nadjem rjesenje ali nisam uspio.
da vidimo sta kaze…
Probaj komandu modprobe tg3 pa javi da li se šta popravilo.
Ako ne, pošalji izlaz one gore naredbe a takođe i lspci.
Kada ukucam dmesg ne ispise nista , a evo ispis lspci
Ethernet controller: Broadcom Corporation Unknown device 1713 (rev 02) , to je samo dio ,da ne stavljam citav ispis
Pa lijepo bi bilo da staviš čitav 
Pa ako bas insistiras 
00:00.0 Host bridge: ATI Technologies Inc Unknown device 7910
00:01.0 PCI bridge: ATI Technologies Inc Unknown device 7912
00:04.0 PCI bridge: ATI Technologies Inc Unknown device 7914
00:05.0 PCI bridge: ATI Technologies Inc Unknown device 7915
00:06.0 PCI bridge: ATI Technologies Inc Unknown device 7916
00:12.0 IDE interface: ATI Technologies Inc SB600 Non-Raid-5 SATA
00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0)
00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1)
00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2)
00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3)
00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4)
00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI)
00:14.0 SMBus: ATI Technologies Inc SB600 SMBus (rev 14)
00:14.1 IDE interface: ATI Technologies Inc SB600 IDE
00:14.2 Audio device: ATI Technologies Inc SB600 Azalia
00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge
00:14.4 PCI bridge: ATI Technologies Inc SB600 PCI to PCI Bridge
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc Unknown device 791f
02:04.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b6)
10:00.0 Ethernet controller: Broadcom Corporation Unknown device 1713 (rev 02)
Našao sam dosta ljudi sa istom tom karticom koja radi kako treba… dmesg mora ispisati nešto, jesi li siguran da kucaš ispravno? Pošalji izlaz naredbe ifconfig. Probaj i ovo:
lspci -n | grep 10.00
pa ćemo potražiti još na netu. Jesi li probao onu modprobe komandu? Pošalji zadnjih par linija ispisa dmesg komande (samo dmesg, bez ičega) nakon što izvršiš modprobe.
Evo sta ispise ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:64 errors:0 dropped:0 overruns:0 frame:0
TX packets:64 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4384 (4.2 KiB) TX bytes:4384 (4.2 KiB)
Dmesg
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
pnp: the driver 'parport_pc' has been registered
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
usb 6-3: new high speed USB device using ehci_hcd and address 3
usb 6-3: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
A lspci ispise
Kada ukucam modprobe tg3 ne desi se nista
Jel ovaj dmesg prije ili nakon modprobe? Probaj i ovako:
rmmod tg3
modprobe tg3
dmesg
Probao sam , nista se ne desava.A taj ispis dmesg je poslije modprobe-a.
:s ništa, ne kontam. Ta kartica bi morala raditi sa tg3 drajverom (provjerio sam nekoliko puta). Onaj ID što ispisuje lspci -n je 100% identifikacija kartice. Osim toga, tg3 bi morao nešto ispisati u dmesg prilikom modprobe, radilo - ne radilo… nemam više ideja 
Vjerovatno je modul već učitan, pa onda komanda “modprobe tg3” ne radi ništa korisno (te nema ništa u dmesg logu).
Output komande lsmod? (ili “lsmod | grep tg3”)?
Najbukvalnije(desava se ): ifconfig eth0 up
Meni se desavalo,da je modul prisutan i sve OK medjutim interface se nije “podigao”
:kul:
@adis: Pa zato sam i rekao da kuca rmmod tg3 pa modprobe tg3, osim toga ranije čovjek napisa da dmesg | grep eth nije ispisalo ništa…
@amar-ze: vidiš moguće je i to…
Probao sam modprobe pa onda ifconfig , ali nista , ifconfig ispise no such interface (ili tako nesto)
Probaj eth1 eth2 …